Start with the tool you want to run
A compressor's biggest printed number is an easy place to begin shopping and a poor place to finish. You need to connect its air delivery to the actual air tool, the tool's working pressure, and the way you intend to use it.
Write down the tool model before you compare compressors. A small brad nailer, an impact wrench, and a sanding tool can all use compressed air while asking very different things of the supply.
Your project matters too: installing a few trim pieces and using a tool continuously are different patterns of demand. Describe the work in plain language before treating a specification table as an answer to your whole project.
This guide helps you organize that comparison. It does not size a permanent compressed-air installation, promise a particular run time, or establish that any combination is suitable without its own instructions.
Keep pressure and delivery together
PSI describes pressure, while SCFM describes an amount of air delivered per minute under standardized reference conditions. For a useful comparison, keep the delivery figure attached to the pressure at which the maker reports it.
DEWALT's support table illustrates why the pair matters. Its listed D55146 output changes from 6.5 SCFM at 40 PSI to 5.0 SCFM at 90 PSI; those are different points for the same documented model.

That is an illustration from a support page updated in 2022, not a claim about today's inventory or a recommendation to buy that compressor. Check the precise manual and specification for any model you are actually considering.
If you copy only the larger delivery figure into your notes, you may compare it against a tool requirement stated at a different pressure. The numbers can look reassuring while failing to answer the question you meant to ask.
Read the tool's definition of demand
Find the tool's air consumption and its required operating pressure in the original documentation. Pay attention to whether the consumption is described as average, continuous, or measured under another stated duty pattern.
Do not treat two different definitions as interchangeable just because both use a volume-per-minute unit. If the documentation leaves the measurement basis unclear, put that question on your list for the manufacturer instead of supplying your own conversion.
For an original worksheet example, imagine Tool A lists a stated requirement at 90 PSI and Compressor B lists its delivered flow at 90 PSI. You now have a comparable starting point, although you still need the conditions and operating limitations behind both figures.
Write the complete pair into one cell: requirement, pressure, and definition. This prevents you from accidentally borrowing the pressure from one table row and the delivery from another when you return to the project later.
Do not use tank size as a flow rating
Tank capacity and delivered airflow describe different aspects of the machine. A larger stored-air volume does not, by itself, tell you what the pump can deliver while your tool continues consuming air.
You can think of the tank as part of the operating system rather than a substitute for the delivery specification. Keep its capacity on the worksheet, but do not use gallons to fill in an SCFM value that the manufacturer has not provided.
The same caution applies to maximum tank pressure. A large maximum-pressure number does not establish the tool's working pressure or prove that the outlet supply will satisfy the tool throughout your intended task.
Avoid turning these observations into a homemade runtime formula unless you have the necessary engineering information. A simple buying worksheet can be useful without pretending it predicts recovery, temperature, noise, or continuous performance from a few headline numbers.
Include the hose and connections
The air has to travel through a real path between compressor and tool. Record the intended hose length, inside diameter, fittings, and any required treatment equipment rather than stopping your comparison at the compressor outlet.
Your tool's manual is the place to find its particular hose and inlet requirements. A specification printed on a hose package cannot establish that the same hose is appropriate for every tool that happens to connect to it.
For your worksheet, draw a line from the outlet through each connection to the tool inlet. Mark an item as unknown when you have not identified its requirement, instead of assuming an adapter solves every difference.
This small drawing can reveal a missing component before you place an order. It also gives support staff a clearer question about the connecting hardware than a general request to approve the compressor and tool.
Match your working pattern honestly
Describe how you expect to use the tool during a normal session. You might be making several short operations with pauses for layout, or you might expect to hold a tool on a surface for a sustained period.
Do not convert your own guess about those pauses into a manufacturer-approved duty cycle. Use the compressor's instructions for its operating limits, then ask whether your planned work fits those limits.
An original example is a weekend project with repeated marking and assembly between short fastening operations. That pattern may prompt different questions from a job where the tool is expected to run steadily, even before you compare model names.
Keep your expectations separate from observed results. Until you have used an approved combination under defined conditions, phrases such as “never waits for recovery” or “runs every air tool” would go beyond the evidence on your worksheet.
Build a comparison you can audit
Give each candidate a column with its exact model and a link to the original manual or specification page. Then add the delivery-pressure pair, tank capacity, power-supply requirements, and any stated operating restriction relevant to your task.
Use a separate row for your tool's requirement so it remains visible beside every candidate. If one listing omits the pressure behind a flow number, mark that omission rather than treating the number as equal to a fully specified value.
Keep the seller's package description in another row. A bundle containing a hose or accessory is a purchasing detail, while the compressor's documented delivery is a technical fact; mixing them makes the comparison harder to follow.
You can also add a short “question still open” row for each model. One unresolved requirement is often more useful to investigate than a long list of attractive features that have no bearing on the tool you need to run.
Ask a precise final question
Before buying, state the complete proposed combination: compressor model, tool model, intended hose path, power supply, and the sort of work you expect. Ask the manufacturer about the unresolved compatibility or operating limit you have identified.
If the answer is conditional, keep the condition with your notes. A reply that applies to intermittent use should not quietly become a promise of continuous operation when you compare the same machine with another task.
Keep the worksheet after the purchase, because your next air tool may have a different requirement. You can reuse the verified compressor information while checking the new tool on its own terms.
The useful result is a documented match for a defined job. Reading SCFM and PSI as a pair gives you a better starting point than choosing whichever tank or maximum-pressure number looks largest on the shelf.
If you share the garage, include storage and setup time in the practical decision. A technically suitable combination still needs a place where you can connect it, inspect it, and put it away according to its instructions without turning every small task into an obstacle course.
Sources behind this guide
Checked October 15, 2026. Sources support the identified facts; examples and worksheets are original editorial analysis.
- DEWALT SCFM ratings support table, updated 2022Flow paired with pressure; D55146 documented example 6.5 SCFM at40PSI and5.0 at90PSI. Historical example, not stock claim.
Read the complete instructions for your exact equipment. Product identities are checked separately from stock, price and seller terms.